How To Replace A Bathtub (For Newbies).
How To Replace A Bathtub (For Newbies).
Blog Article
What're your ideas regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is additionally a reasonably difficult task. If the old bathtub is easily easily accessible, the job can move quickly; if you have to open up a wall surface to eliminate the old tub and position the new bathtub, the job is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub and embeded in the new one. Ensure you have qualified on your own for the task as well as are comfortable trying it. As opposed to employing a professional to take control of a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This short article will certainly assist you set up a brand-new tub in your restroom if you have actually currently purchased a brand-new bathtub and do not need to transform the plan of your previous supply of water pipelines.
Your devices and product checklist need to make up the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the limited access that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the remaining water that will originate from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in place between the tap as well as the sink. Safeguard the faucet in position with the manufacturer offered backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical tap ports. The previous kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the tub until the spirit level reads degree.
To mount faucets, fit all-time low of the furthest versatile tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water as well as inspect all joints and new pipework for leaks and also tighten them if essential. Fill up the tub and also examine the overflow electrical outlet as well as the normal outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized at least once as this will certainly settle it into its last setting.
Preparing for the Installment
To start with, the supporting frame provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you utilize every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to split an inflexible seal, causing the water to pass through the wall surface between the bath and also the tiling, leading to problems with wetness and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components as well as installations. They are marketed in tubes and cartridges, as well as are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can crack fairly early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly offered on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very eager about How to Install a Bathtub Yourself and I hope you enjoyed the new blog entry. Those who liked our article if you please be sure to pass it around. We cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Call Report this page